437 Search Results for: “external”

This 2.54mm 16 Pin Female Flat Ribbon Cable Connector is usually seen for internal peripherals in computers, such as hard drives, CD drives and floppy drives. Flat Ribbon Cable Connector, On some older...

Product Overview The NEO-7M GPS module provides reliable satellite positioning for your Arduino, Raspberry Pi, or microcontroller projects. Featuring a high-sensitivity receiver and micro USB interface, this module delivers accurate...

This is PIAIC Quarter 2 IoT Starter Kit with all basic required components. This PIAIC Starter kit has STM32F3Discovery or STM32F303VC Board, FT232 board, jumper wire, breadboard, led's, resistors, and necessary...

L7812 Voltage Regulator L7806/LM7806Voltage Regulator is a12V voltage regulatorthat can provide local on-card regulation, eliminating the distribution problems associated with single point regulation. Each type employs internal current limiting, thermal shut-down...

The IRF520 transistor load control driver module is used to connect up to 120W DC loads to an Arduino controller or other microprocessor control device. The module can perform switching function...

This sensor serves as a replacement for a PIR sensor and works on the basis of microwaves and the doppler effect. Due to a difference in speed, this sensor can...

Description:Features: 150 x 110 x 70mm external size, ABS waterproof sealed junction box with rubber cut out, the rubber seal hole 26mm diameter. Elegant external shape, high firmness. Applications: Indoor...

This is PL2303 CH340G USB To TTL(Serial) Converter For Arduino Nano Raspberry Pi USB to TTL / USB-TTL /STC microcontroller programmer / PL2303 in nine upgrades plate with a transparent...

HX1838 Infrared Remote Control Module NEC Code The HX1838 Infrared Remote Control Module is a compact and high-sensitivity IR receiver sensor based on the HX1838 chip. Designed for compatibility with...

UT347A Leeb Hardness Tester UT347A Leeb Hardness Tester is accurate and portable in size. It supports thermal printing and is especially suitable for field hardness testing of large equipment such...

Description The SN74LS125N is a Quadruple Bus Buffer with 3-State Outputs, manufactured by Texas Instruments and housed in a standard 14-pin DIP through-hole package. This device contains four independent non-inverting...

TL431 Regulator is three terminal programmable shunt regulator diodes.TL431 Regulator operate as a low temperature coefficient zener which is programmable from Vref to 36 V with two external resistors.  Datasheet Link...

The Device is a monolithic integrated high voltage, high current four channel driver designed to accept standard DTL or TTL logic levels and drive inductive loads (such as relays solenoids,...

3.7V 400mAh 602035 Rechargeable Lithium Polymer Battery – LiPo Cell To begin with, the 3.7V 400mAh LiPo Battery offers a lightweight and compact power solution for various devices. Next, it...

The DRV8825 stepper motor driver carrier is a breakout board for TI’s DRV8825 micro-stepping bipolar stepper motor driver. The Stepper Driver module has a pinout and interface that are nearly...

TO220  INSULATING BUSHING Plastic Diameter  3mm High quality insulating bush for TO-220 package devices. Good quality material and high temperature resistant.These Bushing and insulating particles have good electrical insulation and...

UNI-T UTG1022X-PA — The UNI-T UTG1022X-PA is a 20 MHz dual-channel arbitrary waveform generator built around a 16-bit DAC and 200 MSa/s sample rate, with a built-in 4 W power...

ESP32-S3 HMI 1.9" Smart Display: Revolutionize Your IoT Projects with Arduino & LVGL Unlock the full potential of your Internet of Things (IoT) and human-machine interface (HMI) applications with the...

Arduino Due Microcontroller Board is based on the 32-bit processor Atmel SAM3X8E ARM Cortex-M3 MCU and improves all the standard Arduino functionalities and adds many new features. The Arduino Due offers 54...

The Device is a monolithic integrated high voltage, high current four channel driver designed to accept standard DTL or TTL logic levels and drive inductive loads (such as relays solenoids,...

D4184 dual MOSFET driver module  This module is a breakout board for D4184 MOSFET transistor. This module is designed to control large DC loads with only 1 digital pin microcontroller...

The digital thermometer-hygrometer HTC-2  is a combined device for measuring indoor temperature and humidity. The air temperature and humidity meter is used to control the microclimate parameters in residential, industrial...

ATTINY85-20PU ATTINY85 20PU ATTINY85- 20 ATTINY8 is high-performance, low-power Microchip 8-bit AVR RISC-based microcontroller combines 8KB ISP flash memory, 512B EEPROM, 512-Byte SRAM, 6 general purpose I/O lines, 32 general...

Description: The FSQ0265RN, marked "Q0265R" on the package with the ON Semiconductor logo, is an integrated PWM controller and high-voltage power MOSFET (SenseFET) combined in a single 8-pin DIP package,...